But you are missing the point here, which is to download the iPhone update with the firewall turned off, then install the iTunes update. Lost lagoon the trail of destiny hints ps4. Then you can re enable your firewall if you want. If the firewall is causing you download problems, what else are you going to do? There are times when things may go wrong with the phone or touch and you may need to restore the device to factory settings and start over. This guide explains how to restore the phone to factory settings using iTunes. Note: You need itunes 7.4 or greater for FW versions 1.1.1 and 1.1.2. You need 7.5 or greater for 1.1.3 and 1.1.4. Note: If you intend to jailbreak to install 3rd party apps, prior to restoring, be sure that the firmware version you are using can be hacked. • Dock phone on PC and load iTunes. • Once iTunes recognizes the phone, select the phone • Click the restore button and agree to the prompts. ITunes will download the latest firmware and restore your device. Note: if you need to restore a specific version of firmware onto your device, rather than click restore, hold shift (PC) or option (MAC) and click restore. This will bring up a browse box where you can select the firmware you wish to program. Troubleshooting: If you have any problems with the restore, try using. This will often result in a working restore. Error 1011, 1013, 1015 at the end of restore: This means that the modem firmware could not be updated. If you are performing a downgrade (1.1.4 to 1.1.3, for example), this is normal. You will need to use a tool like (MAC) or (PC) to boot the phone out of recovery mode then your downgrade should be completed. If your phone says “needs repair” and you tried to restore and got this error, you probably have a permanently damaged phone. You can try the DFU mode suggestion above and hope for the best. Error 1602, 1603: This is somewhat of an unknown error. It usually means the PC lost communications with the phone. A reboot may fix it or restarting the apple mobile device service. You may need to reinstall iTunes. In some cases it can be more serious and may require Apple support. You may get lucky if you try to restore without a sim card inserted. (Remove simcard, reboot phone into restore mode, then try again). Common and proper noun writing activity first grade. Error 1600: On OSX, try mkdir ~/Library/iTunes/”Device Support”. If that directory is already there, try removing any files in it. Error 1604: Apple wrote an article on this: Error 1, 2, 3, 6 or some low number. • Perform USB isolation troubleshooting, including trying a different USB port directly on the computer. See the advanced steps below for USB troubleshooting. • Put a USB 2.0 hub between the device and the computer. • Try a different USB 30-pin dock-connector cable. • There may be third-party software installed that modifies your default packet size in Windows by inserting one or more TcpWindowSize entries into your registry. Your default packet size being set incorrectly can cause this error. Contact the manufacturer of the software that installed the packet-size modification for assistance. • Connect your computer directly to your Internet source, bypassing any routers, hubs, or switches. You may need to restart your computer and modem to get online. • Try to restore from another known-good computer and network. Error 18 (or -18): This occurs when the media library on the device is corrupt and cannot be modified or updated. Updating to the latest version of iTunes and then restoring should resolve this issue. Error 19 (or -19): The full text of this error is: “iTunes could not sync to the iPhone ‘[iPhone name]‘ because an unknown error occurred (-19)”. This error can occur when you attempt to update an iPhone 3G to a later version of the software and iTunes attempts to back up iPhone while it is syncing. To resolve this issue. • Deselect “Automatically sync when this iPhone is connected” from the iTunes Summary tab. • Eject iPhone. • Reconnect iPhone. • Select Update. Error 20, 21, 34, 37: These errors typically occur when security software interferes with the restore and update process. If you are using a PC, follow to resolve this issue. Error 23, 28, 29: These errors may indicate a hardware issue with your device. Follow the steps in this article. Also while connected with the white USB Dock Connector cable that shipped with your device, on a known good computer and network to isolate this issue to the device. The or the IMEI being the default value, (00 400 0), can also confirm a hardware issue. Can also cause these errors. Error 35: You can resolve this error by using a known-good 30-pin USB Dock Connector cable. If that does not resolve the issue, follow the instructions for errors 13 or 14 above. Error 40: This error may indicate a hardware issue with your device, but it is typically caused. Follow the steps in this article. Also while connected with a known-good 30-pin Dock Connector cable, computer, and network to isolate this issue to the device. The or the IMEI being the default value, (00 400 0), can also confirm a hardware issue. Error 48 (or -48): Quit iTunes and discard the.ipsw file. Then, open iTunes and attempt to download again. See the steps under the heading “Rename, move, or delete the iOS software file (.ipsw)” below for.ipsw file locations. Error 50: This error (and error -50) are timeout errors. Follow the steps for errors 13 or 14 above. Error 1000: If this error appears in the iPhone, iPad, or iPod updater log file, there has been an error decompressing and transferring the IPSW file that is downloaded by iTunes when restoring your device. This error is frequently caused by third-party security software interference, a poor quality Internet connection resulting in a corrupted IPSW file, or a conflict with other devices connected to your computer using USB. Error 1002, 1011, 1012, 1014: These errors may indicate a hardware issue with your device. Follow the steps in this article. Also while connected with a known-good 30-pin Dock Connector cable, computer, and network to isolate this issue to the device. The or the IMEI being the default value (00 400 0) can also confirm a hardware issue. Error 1004 and 1013: These errors may be the result of the connection to gs.apple.com being redirected or blocked. Follow these steps to resolve these errors: • Check security software. Ensure that communication to gs.apple.com is allowed. Follow this article for assistance with security software.. • Check the hosts file. The restore will fail if there is an active entry to redirect gs.apple.com. Follow to edit the hosts file or revert to default on Windows. See section “Blocked by configuration: (Mac OS X/Windows) > Rebuild network information”. • Try to restore from another known-good computer and network. • If the errors persist on another computer, the device may need service. Error 1015: This error is caused by attempts to downgrade the iPhone, iPad, or iPod touch’s software. This can occur when you attempt to restore using an older.ipsw file. Downgrading to a previous version is not supported. To resolve this issue, attempt to restore with the latest iPhone, iPad, or iPod touch software available from Apple. This error can also occur when an has occurred. Error 1479: This error occurs when trying to contact Apple for an update or restore. Quit iTunes, disconnect from USB, restart the iOS device, reconnect the device to the computer, then launch iTunes and attempt to update or restore again. Error 1600, 1601: Uninstall and reinstall the latest version of iTunes (see instructions for and ). If that doesn’t resolve the issue, see the steps for 1602. Error 1602: Try the following steps to resolve this error. • Ensure proper USB isolation troubleshooting has been performed, and test with a known-good cable. • Follow the steps listed for Error 1604. • This error may be resolved by disabling, deactivating, or uninstalling third-party security, antivirus, and firewall software. See steps in for details on troubleshooting security software.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |